Thirty years of gutter work in Clay and Ray counties. Five and six inch K-style and half round, rolled on site so there is no joint in the middle of a run to come apart in four years, plus downspouts, leaf guard, repairs, resets and cleaning. We come and measure for nothing and you get a written number the same week.
Thirty years in the trade · Rolled on site, no joints in the run · Free measure, written quote the same week
What we install
Nearly every house we do is five inch K-style, and the ones that need six inch are usually the ones with a big steep roof dumping into a short run. We will tell you which one you have when we measure, and we will tell you if the answer is that your existing gutter is fine and the problem is a downspout in the wrong place, which it is more often than anybody in this trade admits.
The standard residential gutter and the right answer on most houses. Rolled in one piece from the coil on the truck, hung on hidden hangers screwed into the fascia every two feet, not spikes. Corners are mitred and sealed on site. Aluminum in .027 gauge, which is heavier than the .019 the big outfits price against.
from $9 a foot
For a big roof, a steep pitch, a long valley, or any place where the existing gutter overshoots in a hard rain. Six inch holds about forty percent more, and paired with a three by four downspout instead of the standard two by three it moves roughly double. This is the fix when somebody says their gutter overflows even though it is clean.
from $12 a foot
Half round in aluminum for houses where K-style looks wrong, and copper for the ones where it matters. Copper is roughly three times the price of aluminum and it is the only gutter we install that people ask for by name. Bracket-hung, soldered corners.
quoted per job
Micro-mesh screen over the top, fastened to the gutter and not under the shingle, which is what voids roofing warranties. It keeps leaves and shingle grit out. It is not magic and nothing is: under a big pin oak you will still be blowing the top of it off once a year, and we say that before you buy it rather than after.
from $8 a foot
Sagging runs pulled back to pitch and re-hung, joints resealed, downspouts re-routed, and rotten fascia board replaced before new gutter goes on it, which has to happen in that order and often does not. Small repairs are worth doing and we do them; we are not going to quote you a whole house because one corner leaks.
from $95
Cleaned out by hand, bagged, and the downspouts run through and flushed so we know they are actually clear. Priced by the house and not by the foot, and we will tell you at the same time whether anything is coming loose up there.
from $145
What it costs
A typical single story ranch runs about 160 feet of gutter with four downspouts, which puts a straightforward five inch job in the range of $1,800 to $2,400 installed. Two story and cut-up rooflines cost more because of the ladder work, not the material. Colour does not change the price; sixteen colours come off the coil at the same number and copper is quoted separately. Tear-off and haul-away of the old gutter is included. We do not ask for a deposit on a residential job and we invoice when it is finished and you have looked at it. Prices here are illustrative for this preview.
Recent jobs
Look at the corners and look at where the downspouts land. A mitred corner cut and sealed on site sits tight to both runs with no gap you can see from the ground. And a downspout that dumps two feet from a foundation has moved the problem rather than fixed it, so we run them out, or into a buried line, and that is part of the job rather than an extra.
The shop
Owner name goes here has been hanging gutter in this part of the state for about thirty years, most of it inside a thirty mile circle around Excelsior Springs. It is a small outfit on purpose. The person who measures your house is the person who rolls the gutter and the person who hangs it, and if something is wrong in two years that is the same person who comes back.
The reason this page exists is a spelling. Search the name and half the directories carry it one way and half carry it the other, so the reviews, the ratings and the phone numbers are split between two listings that are the same man and the same truck. Somebody who hears the name at a neighbour's house and types it in gets a coin flip. This page is the one address on the internet with the name spelled one way, one phone number on it, and no lead broker in between taking a cut for handing your job to three other contractors.
Owner name goes here, Excelsior Springs
Service area
123 Main St
Excelsior Springs, MO 64024
There is nothing to come and look at here, it is a shop and a trailer. Everything starts with a phone call and somebody coming to measure, usually inside two or three days. If you want to see colours, we bring the sample chain to the measure and you hold it against the house, which is the only way anybody has ever picked a gutter colour successfully.
We measure in the afternoons and install in the mornings, so if you call during the day the phone may go to voicemail from a ladder. Leave the town and the street and it gets returned that evening. After a heavy rain or a windstorm the call volume triples for about a week, and in that stretch we take the ones where water is getting inside the house first and everything else in order.
Towns we cover: Excelsior Springs, Kearney, Lawson, Holt, Richmond, Orrick, Camden, Wood Heights, Liberty, Smithville, Plattsburg, Polo, Rayville, Hardin, Henrietta and the houses on the county roads through eastern Clay and western Ray.